Riders who film from the helmet obsess over the camera and almost never over the bracket holding it. That is backwards. The mount decides the angle of your POV shot, how much road vibration shakes the frame, how much wind noise reaches the microphone, and whether the whole thing stays put at speed.
We spent six weeks sorting through ten of the most-reviewed helmet mounts available now, from torsion-spring chin clamps to silicone strap mounts and curved adhesive pads. We looked at what each one clamps onto, how it attaches to the camera, whether the visor still shuts, and what riders say after a season of real use rather than one clean ride around the block. If you are still choosing a camera first, our action camera roundup for motorcycles is the place to start.
This guide covers the best action camera mounts for helmets, organised by mount type rather than by brand, because the mount type is the decision that matters. A mount that glues permanently to one shell is wrong for anyone who owns two helmets. A strap that crosses the chin bar is wrong for anyone who rides in traffic with a sealed visor. A chin clamp is wrong for an MX helmet with no chin surface at all.
Table of Contents
- Top 3 Best Action Camera Mounts for Helmets (October 2026)
- Best Action Camera Mounts for Helmets in 2026 at a Glance
- 2. Lupholue Chin Strap Mount: The Most-Watched Strap Mount Here
- 3. TELESIN 180 Degree Chin Mount: Best Fit for Awkward Helmet Shapes
- 4. TELESIN J-Hook Chin Strap Mount: Built for Dirt Bikes and E-Bikes
- 5. MotoRadds Flex Slim: The Mount That Bends to Fit Your Helmet
- 6. Haoyou HY-414: The Most Adjustable Strap Mount in the Group
- 7. Lupholue Adhesive Curved Pad Kit: Nothing Across Your Face
- 8. SEASKY A1 Flexible Adhesive Mount: The Two-Pack for 360 Shooters
- 9. K and F CONCEPT Chin Strap Mount: Best for MTB and Slopestyle Helmets
- 10. D and F Helmet Chin Strap Bracket: The Simple Starting Point
- How to Choose the Right Helmet Mount
- How to Mount a Camera Without Ruining Your Helmet
- Safety and Legal Notes Before You Glue or Drill
- Frequently Asked Questions
- Final Verdict
Top 3 Best Action Camera Mounts for Helmets (October 2026)
Three mounts came out ahead on the balance of rating, review volume and build quality. The Dango Design Gripper is the one we would put on our own helmet, the Lupholue strap mount is the safest first purchase for a new rider, and the TELESIN 180-degree chin mount handles awkward helmet shapes better than anything else in the group.
Dango Design Gripper Mount
- Strap-free torsion spring clamp
- Up to 2.5 in thick
- Includes safety leash
TELESIN 180 Degree Chin Mount
- 180 degree pad adjustment
- Food grade silicone pad
- Flip adapter
Best Action Camera Mounts for Helmets in 2026 at a Glance
Every mount below reaches the camera through either the three-prong finger interface or a 1/4-20 screw, and all ten work with mainstream GoPro, DJI Osmo, Insta360 and AKASO bodies. What separates them is how they touch your helmet.
| Product | Specs | Action |
|---|---|---|
| Dango Design Gripper Mount |
|
Check Latest Price |
 Lupholue Chin Strap Mount |
|
Check Latest Price |
| TELESIN 180 Degree Chin Mount |
|
Check Latest Price |
 TELESIN J-Hook Chin Strap Mount |
|
Check Latest Price |
 MotoRadds Flex Slim Chin Mount |
|
Check Latest Price |
 Haoyou HY-414 Chin Mount |
|
Check Latest Price |
 Lupholue Adhesive Curved Pad Kit |
|
Check Latest Price |
 K and F CONCEPT Chin Strap Mount |
|
Check Latest Price |
 SEASKY A1 Flexible Adhesive Mount |
|
Check Latest Price |
 D and F Helmet Chin Strap Bracket |
|
Check Latest Price |
1. Dango Design Gripper Mount: Strap-Free Chin Clamping Without Adhesive
Dango Design Gripper Mount for GoPro/Osmo/Insta360 | Universal Helmet Clamp Mount for Action Cameras | Dirtbike, Motocross, Enduro, Motorcycle, and ATV Helmets | Stealth Black
Clamp mount
Plastic, waterproof
Up to 2.5 in thick
3 oz
1-year warranty
Pros
- Torsion-spring jaw grips irregular chin guard shapes firmly
- Nothing strapped across your face so visor and chin vent stay usable
- Includes safety leash thumbscrew and short extension arm
- Doubles as handheld stabilizer or mini tripod
- Higher rating than any other mount in this roundup
Cons
- Clamp capacity stops at 2.5 inches thick
- Needs a chin bar with real substance to bite into
- Only fits cameras with the standard finger mount
This is the mount we ended up recommending to everyone who asked. The jaw is driven by a dual torsion spring with a flexible front web, so it conforms to an awkward chin guard instead of trying to flatten it.
Pull the handle back, press it onto the chin bar, release, and the spring does the rest. Riders describe it on r/motorcycles as the clamp that fits their Shoei properly.
The same pattern repeats in r/gopro threads where people explain that they like a mount which comes on and off so they never have to glue anything to a helmet. That is exactly the use case here: you carry the camera to whichever bike you are riding and clip it on in a parking lot.
Nothing crosses your face. Your visor opens, your chin vent opens, and the camera sits under the visor lip where the wind has already been broken by your riding position. Audio improves for that reason alone.
How it holds up in rough terrain
The included safety leash is not decoration. Riders on advrider.com describe preferring a two-point connection over a single stick, and this mount lets you add one without drilling anything.
Over motocross jumps, washboard enduro roads and winter descents, the spring keeps the camera planted and the footage stays usable instead of shimmering. The web on the front of the jaw spreads the load so the camera does not dig a hard point into the shell.
Where it falls short
The jaw has a ceiling of 2.5 inches. If your chin bar is thin, the clamp has little to grab, and you will feel it move more than you would like on rough surfaces. MX and peak helmets are the usual offenders.
It also needs the three-prong finger interface on the camera side, which every mainstream action camera has but some 360 models handle differently. If you shoot on a body without that interface, budget for a frame or adapter first.
2. Lupholue Chin Strap Mount: The Most-Watched Strap Mount Here
Lupholue Motorcycle Helmet Chin Strap Mount Compatible with GoPro Hero 13, 12, 11, 10, 9, 8, 7, (2018), 6, Hero Black, DJI Osmo Action 5 pro/4/3/2,Insta360 ONER AKASO Campark YI and More（Black）
Strap mount
Silicone base, plastic
1.76 oz
Arm length 3.5 in
Not water resistant
Pros
- Strap and buckle attachment leaves the helmet completely unmodified
- Compatibility from Hero 3 through Hero 13 plus DJI Insta360 AKASO and Yi
- J-hook base accepts extra accessories
- Light at 1.76 oz with a flexible silicone base
- Well over 3000 reviews to sample from
Cons
- Strap stops the visor closing fully which adds wind noise
- Loose strap ends have nowhere to tuck and rub the chin
- Plastic buckle hardware can feel fragile
This is the mount most people in our group had already owned at some point. It is a silicone base that wraps the chin, a buckle strap that holds it there, and a J-hook where the camera screws on. There is nothing else to it.
With more than 3200 ratings behind it there is a lot of history to read, and the pattern is consistent. The silicone base stretches and grips curved chin surfaces better than hard plastic, and the J-hook lets you add a thumbscrew extension if you want the camera higher.
Reviewers confirm the camera stays put at highway speeds when the buckle is properly tensioned, and that the buckle itself adjusts easily to different chin sizes.
The big draw is reversibility. It comes off in seconds, it goes onto another helmet in seconds, and there is zero adhesive anywhere in the kit. That is the most valued attribute in rider forums, where people repeatedly say they will not glue anything permanently to a shell they might sell or replace.
What you give up with a strap mount
The visor issue is real and it comes up in nearly every review of this design. The strap crossing the chin stops the visor from sealing fully, so you get more airflow at speed, more wind noise on the audio track and a higher chance of fogging in cold weather.
Fit also depends on chin shape. The listing is explicit that it is not suitable for helmets with a long chin, and on a very pointed chin bar the strap can sit awkwardly. Tucking the strap tails into the cheek pads solves most of that, and it is what most owners end up doing.
Durability over the long haul
A small minority of buyers report damage after a hard impact or simple strap hardware fatigue. It is a plastic-and-silicone design at 1.76 oz, so it is light on your chin but not built like a clamp that bites into a chin bar.
Treat it as the portable option you move between helmets rather than a permanent installation, and check the buckle tension before every ride rather than setting it once.
3. TELESIN 180 Degree Chin Mount: Best Fit for Awkward Helmet Shapes
TELESIN 180° Adjustable Motorcycle Helmet Chin Mount for Action Cameras
Strap mount
Plastic, polyester, PVC
2.88 oz
180 degree pad
Water resistant
Pros
- 180 degree pad adjustment follows round or angular race chin shapes
- Food grade non-slip silicone sits comfortably against the face
- One-hand install and removal with reusable fixing tape
- Adapter can be flipped to mount the camera upside down
- Broad GoPro DJI and Insta360 compatibility
Cons
- Straps keep the visor from closing fully
- Plastic tabs can crack where the shell behind them is thin
- Colour can vary from the listing between production runs
The headline feature is the pad itself. Instead of a fixed silicone block, the chin pad bends through 180 degrees, so it can follow the steep chin angle of a race helmet or the shallow slope of a street full-face.
On angular race shapes that usually means the difference between a camera aimed at the horizon and one aimed at the front fender. Riders who complained about framing on other strap mounts tend to end up happy with this one.
The silicone is food grade and non-slip, which matters more than it sounds because it sits directly against your skin through the helmet padding. No sharp edge, no hot spot after an hour in the sun.
Durability is the standout in the reviews here. Several owners report units that survived a full year of mountain biking and multiple hard crashes, in some cases losing the helmet entirely and keeping the mount intact. The adapter also flips, so you can shoot upside down if your setup calls for it.
Angle control compared with plain strap mounts
A fixed silicone pad holds whatever angle the helmet gives it. This one moves. Loosen the screw on the back of the pad, tilt the mounting plate through 180 degrees, tighten it again, and the camera stays where you put it.
That matters for POV framing because chin geometry varies so much between helmet brands and models. The adapter orientation can also be turned over, which helps if you run a camera with a tall housing that would otherwise press into the chin padding.
Where the weak points are
The plastic tabs at the top of the pad can crack when the helmet surface behind them is thin and unsupported, which shows up most on lightweight open-face and half helmets. If that is your shell, check the fit rather than tightening aggressively.
The visor conflict applies here as with every strap mount in this roundup, and colour can vary between production runs. Neither is a deal breaker, but both are reasons to check your delivery before you ride away with it.
4. TELESIN J-Hook Chin Strap Mount: Built for Dirt Bikes and E-Bikes
Helmet Mount for GoPro, Motorcycle Chin Strap Attachment with Extension J Hook Dirt Bike Holder Mounting Accessories for Go Pro Max Hero 13 12 11 10 9 8 Insta360 X5 X4 DJI Osmo Nano Action 3 4 5 Pro 6
Strap mount
ABS Y-shape base, polyester
80 g
Extension J-hook
Water resistant
Pros
- Rounded ABS Y-shape base with no sharp edges against the wearer
- Extension J-hook adds mounting height and angle options
- Soft non-slip silicone keeps the helmet shell scratch free
- One-hand installation works on dirt bike e-bike and modular helmets
Cons
- Mount can swivel in position even when tightened
- Strap blocks the chin vent and visor from closing
- Small internal parts can poke the wearer
- Some camera models need a frame not included
The defining part is the extension J-hook. Where most chin strap mounts put the camera one fixed distance from the chin, this one adds a hooked arm that pushes the camera further out and higher, away from your face and away from the strap line.
Riders using it on dirt bikes tell us that extra reach is what stops the chin bar from filling the frame. On a dirt bike you are standing and absorbing hits, so the chin bar occupies far more of the view than it would on a street bike.
The Y-shape base is entirely rounded. No corners, nothing sharp pressed against the chin padding, and the silicone contact layer keeps the helmet shell free of scratches. It goes on and off with one hand, which is convenient when you are pulling the helmet off in a car park.
Compatibility is wide for the class: GoPro Hero 13 down through Hero 5, Max, Session, the DJI Action range and a long list of Insta360 bodies. A few camera shapes need a frame or an extra adapter that is not in the box, so check your specific model.
Why it is a favourite off road
Extension arms earn their keep off road because the camera ends up further from your body and higher relative to the helmet shell. You get more of the trail ahead and less of your own chin in the frame.
Riders also like that the strap and base cooperate with modular helmets and peak-style shells that a rigid chin clamp would fight. The trade is that you give up some of the structural security a clamp offers in exchange for portability.
Stability is the honest weakness
Multiple reviews point to the mount shifting in position over time even when the strap is tightened. It is a soft strap system carrying a heavier camera at a longer lever arm, so vibration has something to work against.
If your footage needs to stay rock steady, tension the buckle properly and add a safety tether. One reviewer lost a camera to a branch, which is a good reminder that off-road footage and off-road retention demands are different problems.
5. MotoRadds Flex Slim: The Mount That Bends to Fit Your Helmet
MotoRadds Flex Slim Flexible Universal Motorcycle Helmet Chin Mount Kit Bendable Silicone Compatible with GoPro Hero 12, 11, 10, DJI Osmo Action, Insta360, SJCAM, Xiaomi Yi Action Cameras (Black)
Chin mount
Silicone, water resistant
About 0.06 kg
Rotatable
Irregular shape
Pros
- Fully bendable silicone body conforms to unusual helmet shapes
- Very light at roughly 0.06 kg so the chin carries almost no extra load
- Rotatable joint for camera angle adjustment
- Suits motorcycle MTB slopestyle motocross and snowmobile helmets
Cons
- Lowest rated here at 4.1 stars with a 15 percent one-star share
- Silicone-only build is less rigid than clamp or ABS designs
- Retention is weaker than harder mounts under heavy vibration
This is the mount you choose when your helmet has no convenient flat spot. The body is entirely bendable silicone, so you shape it to the contour of your chin bar and it stays shaped.
Riders with unusual or deeply curved chin geometry report that this is the only style that grips properly on their shell. On a slopestyle shell with a pointed chin, or a peaked helmet with a short, sharply raked front, it grips where a rigid base sits on top and rattles.
Weight is the other argument. At roughly 0.06 kg the camera barely registers on your chin, which reduces the neck fatigue you get on a long ride with a heavy body mounted low. The rotatable joint lets you dial the angle without rebuilding the whole fit.
The same flexibility carries across sports. It is listed for motorcycle, mountain bike, slopestyle, motocross and snowmobile helmets, and the silicone base takes a phone as readily as an action camera.
Where flexible silicone wins
Hard plastic bases need a surface that matches them. Silicone does the opposite: it takes the shape of whatever you give it, and it grips curved chin bars that no rigid pad would sit on properly.
It also softens the visor argument. Because the body hugs the chin rather than spanning it with a buckle bar, some riders find they can still close their visor depending on how they route it. That is helmet-specific rather than guaranteed, so test it on your own shell.
Where the flexibility costs you
This listing has the widest spread of ratings in the group. Around 15 percent of reviews are one-star, and the critical mass is not about fit or features. It is about retention: a silicone-only body has less rigidity than a sprung clamp.
Under hard vibration the camera can drift from the angle you set, and that drift shows up as horizon wobble you have to stabilise in software later. Riders chasing the cleanest possible POV should weigh that before choosing.
6. Haoyou HY-414: The Most Adjustable Strap Mount in the Group
Haoyou Helmet Chin Mount Strap Compatible with Gopro Hero 13 12 11 10 9 8 7 and DJI Osmo Action Camera，Motorcycle Helmet Extension Attachment Mounting Accessories (Black)
Strap mount
Plastic, polyester, silicone
1.76 oz
180 degree tilt
1-year warranty
Pros
- 180 degree up and down adjustment plus long and short extension arms
- Anti-slip silicone base with grip particles that protect the shell
- Straps do not block your field of view
- Reported to fit snout-shaped motocross chins
- Long and short thumbscrews included
Cons
- Strap ends need careful tucking or they rub the face
- Vent screen cannot shut fully so a tight seal is hard
- Some users report the mount moving under vibration
- Strap clasps can loosen over time
Haoyou includes two extension pivot arms in the box, one long and one short, each with its own thumbscrew. Combined with the 180-degree tilt, that gives you four practical camera positions from one base.
That is the widest framing range in this roundup without buying a second mount. The short arm keeps the camera tight to the chin for a narrow, natural first-person view. The long arm pushes it forward and down, which opens up the horizon.
The anti-slip base has grip particles moulded into the underside, so the camera stays where you put it instead of creeping. The silicone also keeps the shell free of marks, which matters on gloss finishes.
Riders with motocross helmets and unusually snout-shaped chins report good results, and one owner on an HJC full-face found the visor shut cleanly, which contradicts the usual complaint about strap mounts. Fit here depends more on your helmet geometry than on the mount.
Why two arms beat one
Swapping between the long and short arms takes a thumbscrew, not a toolkit, which means you can change framing between a technical section and a fast road run without stopping.
That flexibility also solves the visor problem in a way most strap mounts do not. Pull the strap up slightly and use the long arm to move the camera clear of where the visor needs to travel. It is a small detail with a real payoff.
What to watch
The strap tails need tucking into the cheek pads or they will rub your face through the liner. It takes five seconds once you know, but it is the first thing new owners complain about.
A small number of users report the mount moving around under vibration and clasps loosening over time, so check the buckle before every ride. With a light camera and smooth roads you will not notice; with a larger body on rough tarmac you will.
7. Lupholue Adhesive Curved Pad Kit: Nothing Across Your Face
Lupholue Motorcycle Helmet Chin Mount Kits with Adhesive Curved Pads Compatible with DJI Osmo Action 6, Osmo Action 5 Pro, Osmo Action 4, Osmo Action 3, Insta360, AKASO, GoPro (Version A)
Adhesive chin mount
Plastic, waterproof
2.08 oz
Flat and curved pads
1-year warranty
Pros
- Adhesive pads attach with no strap across the chin at all
- Flat and curved pads included for different helmet surfaces
- Enlarged adhesive area improves steadiness of the footage
- Extension arm widens the field of view
- Buckle sticker and hanging rope add a second retention layer
Cons
- Adhesive bond is permanent so the pad cannot be repositioned casually
- Some camera models need a frame or adapter not included
This is the option for riders who refuse to have anything across their chin. A pad bonds directly to the chin bar, the extension arm carries the camera, and your visor closes and opens exactly as it did before.
On a street bike in traffic that is a meaningful comfort difference over any strap mount. The adhesive area is deliberately larger than on a standard base, and reviewers credit that with steadier footage.
The kit includes both flat and curved pads, so you are not forced to bond a flat sticker onto a round shell and hope the edges stay down. The arm adjusts up and down for long-chin and short-chin helmets.
There is real attention to retention here. A buckle sticker and a hanging rope are included as a second layer, which is exactly the redundant attachment riders describe preferring when they think about a camera falling off at speed.
Adhesive pros that no other mount offers
Nothing on your face, nothing across the vent, nothing to interfere with a modular helmet release, and the lowest profile of any mount in this roundup. Wind noise drops because the camera sits tucked against the shell rather than hanging off the front of the chin bar.
The bond is genuinely strong when the shell is prepared properly. Clean the surface, press the pad down firmly and leave it alone for the cure period before riding hard. Get that right and it stays put through rain, cold and vibration for seasons.
The decision you cannot undo easily
This is a permanent choice for that helmet. Pads do not come off cleanly, and on a glossy shell or a painted chin bar you can end up with residue or a mark. Anyone who rotates helmets or plans to sell one will regret this within a year.
Test the fit with the pad held in place and no pressure for a full day before you bond it. Decide once, choose the position carefully, and use the included hanging rope on every ride afterwards.
8. SEASKY A1 Flexible Adhesive Mount: The Two-Pack for 360 Shooters
SEASKY 2Pack A1 Flexible Adhesive Helmet Mount use Genuine 3M Adhesive
Adhesive mount
TPU plastic
0.14 kg
Rated to 500 g
1-year warranty
Pros
- Semi-flexible TPU base with a large contact area fits curved helmet shells
- Genuine 3M double-sided adhesive resists temperature humidity wind and rain
- Two pack lets you mount on two helmets or two positions
- Includes two 1/4-20 adapters for 360 and panoramic cameras
- Rated to hold 500 g
Cons
- TPU base tabs can snap so a camera leash is advisable
- One buyer reported the bond releasing on a first ride
- Adhesive is effectively permanent once set
- The 1/4 screw can be pushed out while tightening
This is the one to look at if you shoot 360 video. The kit ships two 1/4-20 adapters so you can bolt on an Insta360 X-series or GoPro Max body without hunting for the right connector.
The 500 g weight rating covers the heavier panoramic cameras comfortably. Most chin mounts assume a standard action camera shape, so the adapters are what make this usable for a 360 setup.
The base is semi-flexible TPU rather than rigid plastic, with a contact area larger than the traditional small pad. On a curved helmet shell that extra footprint and a little flex are what stop the edges from peeling away.
Buyers using it for 360 work on hard hats and job sites report strong adhesion on curved surfaces, and motorcycle users report good results over long periods. It comes as a two-pack, so you can mount in two positions on one helmet or bond a base to each of two shells.
Best used where the shell is round and hard
Flexible TPU performs best on a smooth, curved, non-textured surface. That covers most modern composite and polycarbonate helmets, which is why the reviews skew positive. Textured or fabric-covered shells are a problem for any adhesive base.
The two-pack also gives you a spare. Adhesive failures are sudden rather than gradual, so having a second base already cured on your spare helmet is a genuine advantage if you ride often or in mixed weather.
What the critical reviews flag
Two things come up repeatedly. The TPU base tabs can snap under load, which is why these mounts should be used with a camera leash rather than trusted alone. And the 1/4 screw can be pushed out of its thread while you tighten it.
There is also a documented report of the bond releasing mid-ride despite careful surface preparation. It is a single case rather than a pattern, but it is the reason the included redundancy matters. If you go adhesive, you go adhesive with a tether.
9. K and F CONCEPT Chin Strap Mount: Best for MTB and Slopestyle Helmets
K&F CONCEPT Action Camera Motorcycle Dirt Bike Helmet Chin Strap Mount
Strap mount
ABS plastic
Not water resistant
Dual buckle lock
Rubber backed base
Pros
- Dual-buckle quick-release lock holds the camera firmly with no wobble
- Rubber backing protects the helmet shell from scratches and adds grip
- Extended adjustable straps fit a wide range of chin sizes
- Works with both two-claw action cameras and 1/4-inch screw cameras
- Includes a tilting accessory for setting the recording angle
Cons
- Visor cannot close fully which produces significant wind noise
- Fit and security vary a lot by helmet shape
- POV framing sits lower than an under-visor mount
The dual-buckle strap system is the point of this mount. Two quick-release buckles rather than one means the load is shared and the mount does not creep sideways when you turn your head.
That is what stops the wobble that plagues single-buckle strap designs on rough ground. Reviewers highlight the absence of shake from body movement, which on a bike with no suspension or a hardtail is a meaningful upgrade to image quality.
The Y-shape ABS base is backed with rubber, so it grips the shell and protects the paint at the same time. That combination is why it comes up so often on mountain bike and dirt bike helmets, where helmets take hits.
It is also unusually open about camera compatibility. Beyond the usual two-claw action cameras, the spec covers 1/4-inch screw bodies such as the Osmo Pocket range and several Insta360 models.
Angle control and the tilt accessory
A small tilting accessory is included, and it does more work than it sounds. Strap mounts sit lower on the chin than a chin clamp, so the camera tends to look at the front wheel unless you tilt it up.
The accessory makes that adjustment repeatable rather than a guess, and the ABS base with dual buckle is one of the more rigid strap designs here. On a helmet with little support behind the chin, that rigidity is worth more than a softer fit.
Where fit is the deciding factor
Strap mounts live or die on buckle tension, and a minority of users simply could not get this one to fasten securely on their particular helmet shape. Sit in the helmet with the mount fitted and pull the straps the way you would while riding, not while standing.
Visor interference is the other recurring point. A strap across the chin means wind noise on the audio track and a visor that will not seal, which is fine on a dirt bike with goggles and less fine on a street full-face.
10. D and F Helmet Chin Strap Bracket: The Simple Starting Point
D&F Helmet Chin Mount Motorcycle Helmet Strap Bracket for GoPro Hero 12/11/10/9/8/HERO7/6/5/4/3,DJI Osmo Action/YI/Akaso/Apeman/Acrosstour Action Camera for Bikers, Motorcyclist, Skiing
Strap mount
PC plastic, silicone base
Water resistant
Low profile buckles
Adjustable buckle
Pros
- Simplest way to get a chin-mounted camera working
- Low-profile metal buckles sit flat and do not irritate the face
- Silicone base fits the helmet chin well with a J-hook for quick camera swaps
- Works on both motocross and street full-face helmets
Cons
- Visor cannot close fully while the mount is fitted
- Blocks the helmet front chin vent
- Soft PC lower triangle and rod boss can crack after a few months
- Unsuitable for modular helmets because it hinders the front opening
If you have never mounted a camera on a helmet before, this is the cheapest way to find out whether you like the footage. Reviewers consistently call it a bargain that does the job it advertises.
The detail that sets it apart from generic strap mounts is the buckle hardware. Low-profile metal buckles sit flat against the strap instead of standing proud, so they do not dig into your face when it is tightened.
Several owners single that out as the reason they kept the mount. Underneath, a silicone base conforms to the chin curve and a J-hook accepts the camera, which makes swaps quick.
It is rated water resistant and works on both street full-face and motocross shells, so it is not limited to one discipline. The design has been around long enough that there is plenty of long-term feedback to read.
Honest durability limits
The soft PC plastic is the weak point. Two separate reviewers report the lower triangle and rod boss cracking after a few months of ordinary use, which points to fatigue in the plastic rather than a bad installation.
It also blocks the front chin vent, which pushes warm air into the visor area, and it prevents the visor from closing fully. On a modular helmet it actively hinders the front opening, so it is not the right choice there.
Who should buy it anyway
Anyone on a first camera, anyone who wants a spare mount to keep in a bag, and anyone who wants to try chin mounting before spending more. Set expectations honestly: it is a working mount with a limited service life.
If you keep it, check the lower triangle and the rod boss occasionally for hairline cracks and replace it when you find one. Keeping it as a backup mount for a second helmet is also a sensible use.
How to Choose the Right Helmet Mount
Start with your helmet, not the mount. A full-face street helmet with a solid chin bar supports every category in this roundup. A peak or MX shell with a short, steep chin bar rules out rigid chin clamps and makes adhesive pads unreliable, which leaves strap mounts as the practical answer. An open-face helmet rules out chin mounting entirely.
Next, decide how many helmets you ride. One helmet and a strong preference for low profile points to the adhesive route. Two or more helmets, or any reluctance to modify a shell, points to a strap or clamp. Riders in r/gopro describe the clamp approach as the one that lets them move between helmets without gluing anything to a shell.
Then check visor clearance. If you ride in traffic with a sealed visor, a strap that crosses the chin is a daily compromise on noise and fogging. Riders on r/MotoUK ask specifically about microphone quality on helmet cameras, and the honest answer is that mount placement affects that more than the camera body does.
Finally, look at retention. Riders on advrider.com describe preferring a two-point connection over a single stick, so a mount with a safety leash or a buckle-and-hook combination is worth the extra thought. Whatever you choose, add a tether on any mount that leaves your chin bar. Our camera cleaning kit roundup covers keeping lenses usable after a dusty ride.
How to Mount a Camera Without Ruining Your Helmet
Adhesive mounts get the most attention in installation advice, because they are the only ones where a mistake is permanent. Clean the chin surface with isopropyl alcohol, let it dry fully, and mark your position with masking tape before you peel anything.
Hold the pad in place without pressing for 24 hours before you load it with a camera. Adhesive on a helmet shell may also fall outside what the manufacturer considers a covered or undamaged finish, so check your warranty terms before bonding anything.
For every non-adhesive mount the routine is simpler. Sit in the helmet, fit the mount, tighten the buckle or clamp while wearing it, and check from the side that the camera sits level rather than angled at the road. Then confirm the visor or goggles still close over it.
Tether the camera every ride. A short loop from the camera to the mount or to the helmet strap takes seconds and is the cheapest insurance available. The same fitting logic applies to other mount categories, including the setups in our trail camera mount guide.
Safety and Legal Notes Before You Glue or Drill
Mounting a camera on a helmet is legal in most places, and rules that exist usually concern the camera itself rather than the bracket. A few jurisdictions restrict what you can record, so check your local rules before you ride, particularly if you plan to film other road users.
On the safety side, avoid drilling into a composite shell. Adhesive pads and straps leave the structure intact; holes do not. Riders debate chin mounts and impact behaviour in forums, and the sensible position is to keep the camera low, keep the profile minimal and never compromise the visor mechanism.
Treat the visor as a safety system rather than a comfort feature. Any mount that prevents it from closing properly is a poor trade for a slightly better camera angle.
Frequently Asked Questions
Is it illegal to have a camera on a motorcycle helmet?
Mounting an action camera on a helmet is legal in most countries and states. Where rules exist, they usually address what you may record rather than whether a camera may be attached. A few jurisdictions restrict filming other road users, so check your local rules first. Some helmet manufacturers also state that adhesive or drilled modifications can affect warranty coverage.
Do all action cameras have the same mount?
Most share the same three-prong finger interface, but three standards exist. GoPro-style three-prong fingers cover most GoPro, DJI Osmo, Insta360 and AKASO bodies. A 1/4-20 screw thread serves 360 and panoramic cameras, and magnetic adapters exist for quick swaps. Always confirm your specific camera model is listed before buying, and check whether a frame or adapter is included.
Do all helmets have chin straps?
No. Full-face helmets, modular helmets and most MX helmets have chin bars that chin and clamp mounts can grip. Open-face and half helmets have no chin bar, so chin mounts are not an option and you need a strap or adhesive solution instead. Peak and MX shells often have short, steep chin bars that resist adhesive pads and give a clamp little to bite into.
What is the best camera for a motorcycle helmet?
For helmet filming, mount quality matters more than camera tier. A stabilised body on a secure, low-profile mount produces better footage than an expensive camera on a mount that shifts under vibration. Chin and clamp mounts also cut wind noise compared with top mounts. Our action camera roundup covers the cameras themselves if you are starting from scratch.
What is the best type of helmet mount for an action camera?
A chin or clamp mount is the best general choice because it spreads the weight evenly, lowers wind noise and leaves your visor and chin vent usable. Choose a strap mount if you rotate multiple helmets or refuse to bond anything to a shell. Choose an adhesive base only for a single helmet where a strap-free, low-profile install matters most.
Final Verdict
The Dango Design Gripper is the mount we would fit to our own helmet: a sprung clamp, no strap, no adhesive, a visor that still works, and the highest rating in this group with more than 2300 ratings behind it. Riders who need to move between helmets without touching their shells should look at the Lupholue chin strap mount, the most-reviewed product here at over 3200 ratings.
Beyond those two, the TELESIN 180-degree chin mount handles unusual helmet shapes best, the SEASKY A1 is the answer if you shoot 360, and the Lupholue adhesive kit is the only route to a completely strap-free install on a single helmet. Whichever one you pick, fit it while wearing the helmet, check the visor closes over it and tether the camera before your first ride. Our action camera picks for adventure riding are worth a look if you are building out a wider kit.